RU

Covcheg ESP setup for PUBG

Game guidesPUBG Updated29 October 2026
Working Advanced setup
Download Loader Buy Covcheg ESP — from $2.58

The ESP runs from a flash drive and draws through OBS 25.0.8, with the game in DirectX 11 Enhanced. BIOS needs virtualization, UEFI and Secure Boot off.

Requirements

0 of 4 items

Tick what matches your PC:

  • Windows 10 or 11 (x64)
  • An Intel or AMD CPU with virtualization
  • UEFI boot mode, system disk in GPT
  • A USB flash drive or a virtual one

System requirements

  • Operating system Windows 10 or 11
  • Processor Intel or AMD
  • Graphics card NVIDIA, AMD or Intel
  • Game mode Borderless window or windowed
  • Launchers Steam
  • Built-in spoofer No
You will also need Not included in the purchase — have it ready before you pay
  • USB flash drive Needed to launch
  • OBS Studio 25.0.8 Exactly this version, remove a newer one

Preparation

0 of 8 steps
Enable virtualization (VT-x / SVM) The loader needs hardware CPU virtualization. Enabled in BIOS.
  1. Enter BIOS/UEFI and open Advanced → CPU Configuration (naming varies by board).
  2. Enable Intel Virtualization Technology (VT-x) on Intel, or SVM Mode on AMD. Save and reboot.
A full walkthrough covering every case: How to enable virtualization in BIOS: Intel VT-x and AMD SVM
Enable Hyper-V Needed when the product requirements say Hyper-V must be on. Enabled in Windows features.
  1. Open Control Panel → Programs → Turn Windows features on or off and tick Hyper-V with all its sub-items.
  2. Open Command Prompt as administrator, run the command, then reboot:
    bcdedit /set hypervisorlaunchtype auto
Disk in GPT layout If the loader says “Unsupported firmware”, the system disk is MBR and needs converting to GPT.
  1. Check the layout: Win+R → diskmgmt.msc, right-click the system disk → Properties → Volumes → Partition style. It should read GUID (GPT).
  2. If it's MBR, convert without data loss: admin Command Prompt, run mbr2gpt /convert /allowfullOS. After converting, switch the BIOS boot mode to UEFI.
Back up anything important before converting. It usually goes smoothly, but a disk is a disk.
Disable Secure Boot Secure Boot stops the loader from starting. Check the status first, then disable it in BIOS if needed.
  1. Check the status: press Win + R, type msinfo32, and in System Summary find Secure Boot State. If it reads Off or Unsupported — you're set, skip the rest.
  2. If it's On — enter BIOS/UEFI (tap Del, F2 or F10 while the PC boots — depends on the motherboard).
  3. Find Boot or Security → Secure Boot and set it to Disabled. Save (usually F10) and reboot.
    • If Secure Boot is greyed out, set a Supervisor Password under Security first — that unlocks the option. You can remove the password afterwards.
A full walkthrough covering every case: How to disable Secure Boot: ASUS, MSI, Gigabyte, ASRock and laptops
  1. Check that virtualization is on: Task Manager → Performance → CPU, the Virtualization line should read Enabled.
  2. Set the BIOS boot mode to UEFI (guide).
  3. If Hyper-V is missing from the list, download the bat file, run it as administrator and restart the PC.
  4. In PUBG graphics settings choose DirectX 11 Enhanced.

Launch

0 of 13 steps
  1. Download the loader and move the folder from the archive to a USB flash drive.
  2. No flash drive — create a virtual one with OSFMount.
  3. Unpack all files into one folder, run loader.exe and enter your key.
  4. Select the game and press the launch button.
  5. Start PUBG following the loader prompts, without pressing anything in the loader yet.
  6. Once the main menu loads, install OBS Studio 25.0.8 — exactly this version.
  7. Run OBS as administrator.
  8. In OBS double-click Game Capture and choose Capture specific window.
  9. Pick the PUBG TslGame.exe process and press OK — the game must be running at this point.
  10. Wait until the game picture shows up in the OBS window.
  11. If your graphics card is AMD or Intel:
  12. Install Action! Screen Recorder, switch it to Games mode and wait for the FPS counter in the top right of the game menu.
  13. Press F5 in the loader window and follow its prompts.

Problems & fixes

2
Change game window mode and Press F5
Open the game settings, change the resolution (for example 1920x1080 to 1680x1050 or back), apply and press F5 in the loader.
The loader says a requirement is not met
Open the Configs tab in the loader: the main items should be green. A red item is a preparation step left undone: virtualization, Hyper-V, GPT, UEFI or Secure Boot.

FAQ

1
Do I need a physical USB flash drive?
No, a virtual flash drive works instead.

Still stuck?

Run R1XON Checker first — it pinpoints most launch problems in 30 seconds. If it still fails, attach the checker report to your support ticket and we’ll sort it out fast.

Download R1XON Checker Contact support